How To Change A Water Softener Filter
Kinetico water systems simply and reliably provide you with slap-up h2o quality, simply some require routine maintenance to keep them performing optimally. To ensure proper performance of your Kinetico water softener, change the softener's prefilter regularly. A prefilter will keep sediment and any other solid material in your water supply from inbound your Kinetico water softener. Here's how to change the prefilter.
Contact Your Local Kinetico H2o Proficient for Water Softener Service
How to Modify Your H2o Softener's Prefilter
Stride 1: Put your water softener in by-laissez passer
Locate the by-laissez passer valve installed with your water softener. When in service, your Kinetico past-pass should show a green section in the opening of the punch. Turn the handle of the by-pass valve then the dial shows the yellow section in the opening. Your system is now in the by-pass position. Note: at that place are many by-laissez passer valve styles. Yours may not be as described here.
Step 2: Ready upwards to Depressurize System
The second step is to locate the 3/8" plastic tubing coming from the past-laissez passer/prefilter Superkit. If this tubing does not run to a drain, be sure to place a bucket or receptacle underneath it to take hold of whatsoever water. Annotation: Even if y'all have a Kinetico Superkit, you may not have the described tubing. If non, proceed to step 4.
Footstep 3: Depressurize the h2o softener and prefilter
Locate the 3/8" valves, located at the caput of the prefilter and near the h2o softener connector tubes that bring together the water softener to the pipes. Plough the valves to the open position to depressurize your system. Keep the valves in the open position. This should reduce water spillage and make it easier for you to turn the filter housing. Look at least one minute before proceeding.
Stride iv: Remove the filter sump
After your arrangement has depressurized for a infinitesimal or longer, remove your filter housing sump by turning information technology clockwise with 2 easily (when viewed from above). This may take some effort if you practice not accept the valves and tubing to depressurize your arrangement and the housing is tightly sealed. Some dealers offer a sump removal wrench to make it easier. Have intendance every bit the housing sump will be total of water.
Step 5: Remove the used filter cartridge
Later the housing is removed, turn the filter cartridge clockwise to remove information technology (when viewed from above). Once removed, discard the filter cartridge. If it is a reusable filter cartridge, thoroughly rinse the cartridge with make clean running water until it looks clean, or past soaking information technology in a solution of water and Iron Out, or whatever your authorized, contained Kinetico dealer recommends. When dry, store the reusable cartridge for future employ.
Step 6: Inspect and clean your sump
Afterward discarding the water in the sump housing, look within and meet if sediment or anything has collected at the bottom. Clean the sump, if needed. Before you insert a new or clean cartridge, check to see if your sump's seal and O-ring are in skilful status. If necessary, lubricate the O-ring at the height of the housing with a silicone lubricant. Do non use petroleum jelly or any other lubricant equally information technology will void your warranty. Contact your dealer for an appropriate lubricant, if needed.
Step 7: Install the new or clean filter cartridge
To install the new filter cartridge, insert it into the top of the filter housing, and turn it counter-clockwise until it stops turning.
Step 8: Install the filter sump
After inserting the filter cartridge, place the filter housing over the filter cartridge, lining up the threads and turning the housing counter-clockwise until it seals. Note: For proper alignment, exist sure the arrow on the caput of the filter sump aligns with the arrow on the filter housing.
Step 9: Close the 3/viii" Valves
Return to the ii valves (at the softener connector pipes and the filter caput) and plough them to the closed position.
Pace ten: Set your by-laissez passer to "in-service"
Return to the by-pass valve and turn the handle until the green section shows on the dial. The system is at present in the "service" position. Be certain to check your prefilter for a leak. If you detect water dripping from the housing, you may need to further tighten the filter housing, or something could be preventing the housing from sealing properly. Bank check that the filter cartridge is firmly in place, and that the O-ring is non obstructing the seal.
Larn more about Kinetico H2o Softeners
Y'all take now successfully inverse your water softener's prefilter. Replacing your prefilter regularly will help protect your Kinetico Water Softener.
Note: Your installation may not appear as we've described here. Installations vary by home, equipment installed and dealer. Some Kinetico systems have prefiltration built into the water softening system. If you accept questions about your organization or need help, delight contact your Authorized, Independent Kinetico Dealer.
Contact a Kinetico Water Expert for Help With Your Water Softener
How To Change A Water Softener Filter,
Source: https://resourcecenter.kinetico.com/owners-support/change-your-kinetico-water-softener-prefilter/
Posted by: hayesaltylets.blogspot.com
0 Response to "How To Change A Water Softener Filter"
Post a Comment